Upload log
From Vorpal Robotics Wiki
Below is a list of the most recent file uploads. See the gallery of new files for a more visual overview.
(newest | oldest) View (newer 20 | older 20) (20 | 50 | 100 | 250 | 500)- 17:30, 9 July 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-31.jpg (Mimsy build figure 31.)
- 17:25, 9 July 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-30.jpg (Mimsy build figure 30.)
- 02:34, 30 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-29.jpg (Mimsy Build figure 29. The console fits in the two slots on the rear of Mimsy as shown.)
- 02:29, 30 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-28.jpg (Mimsy Build figure 28. Route the cables as shown and use the console wire plate and two 3/8" screws to hold them in place.)
- 02:15, 30 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-27.jpg (Mimsy Build figure 27. Install the buzzer using two 3/8" screws, do not overtighten. Connect the LCD cable as shown with the black wire at the top.)
- 02:03, 30 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-26.jpg (Mimsy Build figure 26. Attaching the 10cm 3-wire cable to the buzzer. The black wire matches with the "-" marking while the white matches the "S" marking.)
- 03:05, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-25.jpg (Mimsy Build figure 25. The LCD is secured with two screws at the top of the console bezel.)
- 02:59, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-24.jpg (Mimsy Build figure 24. Remove the protective plastic from the LCD before installing.)
- 02:53, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-23.jpg (Mimsy Build figure 23. Installation of Arduino Nano and IO shield on console.)
- 02:42, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-22.jpg (Mimsy Build figure 22. Parts needed to assemble control panel.)
- 02:28, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-21.jpg (Mimsy Build figure 21. The front floor is shown with fence installed.)
- 02:24, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-20.jpg (Mimsy Build figure 20. Installation of battery brackets. Alternate position is for alternative batteries such as 7.2 volt NIMH RC batteries.)
- 02:23, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-19.jpg (Mimys Build figure 19. Parts needed to install battery brackets and fences.)
- 01:51, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-18.jpg (Mimsy Build figure 18. Front view of chassis with servo wires routed to the rear.)
- 01:44, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-17.jpg (Mimsy Build figure 17: using the same locking tab and slot system, take the sensor bar and align and press in first one side and then the other.)
- 01:35, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-16.jpg (Mimsy Build figure 16. Insert the cross bar wire guide in the cross bar and firmly press.)
- 01:31, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-15.jpg (Mimsy Build figure 15. Insert the cross bar with the two square holes facing the side of the servos that have the wires. You need to angle it in. Just loosely put both sides in the slots, don't force it forward to lock yet.)
- 01:10, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-14.jpg (Mimsy Build figure 14. Front and rear floors installed on one drive train.)
- 01:06, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-13.jpg (Mimsy Build figure 13. Make sure the locking tabs are pushed all the way through the slots so they are firmly connected.)
- 01:00, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-12.jpg (Mimsy Build figure 12. The locking tabs will only align one way with the slots in a drive train. Make sure you have the right match-up.)